AOR AR5001D Dokumentacja

® AR5001D Digital Processing Communications Receiver Operating manual AOR, LTD.

9 where they may be intensely monitored. When examining large frequency segments, it is common to find that 90% of the frequencies are inactive and o

10 The I/Q stands for In-Phase/Quadrature-Phase. In the 45.05 MHz IF stage, I/Q output is available as an optional feature. The I/Q digital signal

11  Built-in AFC (Automatic Frequency Control) AM (Amplitude Modulation)  Envelope Detection (Normal AM decoder)  Synchronous Detection 1. D

12 2 CONTROLS AND FUNCTIONS 2-1 FRONT PANEL 1. Power On/Off switch 2. Function switch 3. Analog S meter 4. LCD (Liquid Cry

13 2-2 REAR PANEL 1. Antenna connector 1 (N type) (25MHz~3.15GHz) 2. Antenna connector 2 (N type) (40kHz~3.15GHz) 3. ACC2 (Accessory 2

14 2-3 LCD DISPLAY Frequency display mode Band scope mode Icon Function F Function switch O Dual channel

15 2-4 KEYPAD Keypad conventions Most keys have secondary functions; their functions are printed on the panel. However, due to the restriction of a

16 Press the [SCAN] key again to initiate SCAN. If the receiver stops on an unwanted busy channel during scan, it can be resumed using the [UP] key o

17 3 – IF BW Figure THREE for the numeric input of frequencies, bank, channel numbers, etc. Press the [FUNC] key, and press the [3] key to activate

18 8 - ALARM Figure EIGHT for the numeric input of frequencies, bank, channel numbers, etc. Press the [FUNC] key, and press the [8] key to activate

1 Table of Contents 0 1 INTRODUCTION ...

19 Press and hold the [kHz] for two seconds while an SD memory card is inserted to start recording audio. To stop recording, press the [CLR] key. M

20 The [PASS] key is also used to select on/off of certain options such as step adjust and select defaults in other menus. MHz – ENT/TEXT This key

21 DOWN - SUB In VFO mode, press this key to change the displayed frequency to be incremented in a downward direction by one step. I

22 Press the power switch on the front panel of the AR5001D. As you press the power switch, a ‘click’ will be heard. Please

23 3-3 VOLUME CONTROL To change the volume (audio) level, rotate the volume control (AF gain) clockwise to increase, and countercloc

24 Each VFO has a specific function under certain configurations. VFO-B --- Used for manual search between VFO-A frequency to VFO-B frequency

25 3-5-1-2 CHANGING FREQUENCY USING THE MAIN DIAL In VFO mode, the active VFO frequency may be ‘tuned’ in using the main dial which is mounted on

26 NFM is the most common mode used above 30 MHz with the exception of the airbands. NFM is widely used on the VHF bands: VHF marine band, 2m amateur

27 AIQ – Analog IQ for DRM New digital communication format for SW (Shortwave) broadcast. Proper software and external hardware are required to dec

28 in the U.S.A. is 10 kHz, and is 9 kHz in Europe and Japan. For above reasons, it is necessary to change the frequency step size according to the

2 5-1-3 MOVING THE SPECTRUM ... 33

29 of bandwidth in order to operate. Otherwise the receive system will not produce intelligible sound. Correct receive mode and IF bandwidth must al

30 Mode Bandwidth Remarks Mode Bandwidth Remarks WFM1 (IF100k) 100 kHz N/A below 25 MHz CW2 (200) 200 Hz WFM2 (IF 200k) 200 kHz N/A bel

31 When AGC is set to OFF, the RF gain control can be adjusted. 4-2 ATTENUATOR / RF AMPLIFIER Activating the attenuator reduces signal to the R

32 Press the [FUNC] key, and then press the [ATT] key to activate the antenna input selection menu. The menu has a selection of 1, 2, 3, 4, and PRG

33 5-1-1 ACTIVATING THE SPECTRUM DISPLAY In VFO mode, press and hold the [FUNC] key for two seconds, then the spectrum display screen appears on t

34 5-2-1-1 ACTIVATING DUAL CHANNEL IN OFFSET MODE In VFO mode, press the [FUNC] key, then press the [5] key. The dual frequency d

35 5-2-2 DUAL BAND RECEIVE In VFO mode, one frequency below 25 MHz (defined as Sub frequency) and another frequency above 25 MHz (defined as Main

36 5-2-3 TRIPLE CHANNEL RECEIVE Using both the Dual channel receive mode and Dual band receive mode at the same time, a total of three channels c

37 4. When the configuration menu is displayed, press the [UP] key four times to select “SD FORMAT” in reverse contras

38 6. Press the [MHz] key to exit from this screen. 7. Press the [CLR] key to exit the configuration menu. 5-3-3 READ DATA FROM SD CARD

3 8 SEARCH MODE ...

39 3. Press the [FUNC] key, and then press the [kHz] key. 4. When the configuration menu is displayed, press the [UP] key six times to select “W

40 3. Press and hold the [kHz] key for two seconds. Recording will start and the “SD” icon will change to “REC”. 4. To stop recording, press

41 5-3-7 DELETE FILES To delete a recorded audio file on the SD memory card, perform the following steps: 1. Insert a SD memory card with a prin

42  Antenna input  AGC mode  CTCSS  DCS  Auto notch The alphanumeric comment may be used to ease identification at a later date. The 2,000

43 c) Press the [2] key. d) Press the [3] key. e) Press the [. (decimal)] key. f) Press the [5] key. g) Press the [MHz]

44 i) Rotate the sub dial to select “B”. j) Press the [DOWN] key. k) Press the [2] key. (“A” appears.) l) Press the [DOWN] key. m) Press

45 6-5 DELETE ALL MEMORY CHANNELS IN THE MEMORY BANK To delete the contents of an entire memory channel in the memory bank, perform the following s

46 7-3 SELECTING A SCAN BANK The memory bank identifier (such as “03”) will be displayed on the middle right of the LCD. I

47 7-5-2 DELETE SELECT SCAN CHANNELS IN MEMORY READ MODE To delete all selected scan channels, perform the following steps: 1. Press the [FUNC] ke

48 In memory read mode or while stopped on an unwanted frequency, press the [PASS] key. Pressing the [PASS] key aga

4 10-12 VIDEO OUT (VIDEO OUTPUT) ... 76 10-13 VIDEO

49 The following parameters can be registered for each of the scan groups. • Bank link setting • Scan pause • Scan delay • Voice scan • Mode s

50 2. Select the bank link group number, and then press the [DOWN] key. The pause setting screen will appear. 3. Rotate the sub dial to set s

51 To set the voice scan parameter, perform the following steps: 1. Press the [FUNC] key, and then press the [SCAN] key. The bank link screen will a

52 4. Rotate the sub dial to select voice scan parameter. 5. To confirm entry, press the [MHz] key. To set other parameters, press the [DOWN] key.

53 2. When the receiver stops on a busy frequency, you can resume manual search by rotating the main dial or pressing the [UP] key or [DO

54 8-1-2-4 STOPPING THE SEARCH While the search process is in progress (not stopped), press the [VFO] key (displaying the data on-screen before se

55 8. For example, enter “2M BAND” as a search bank text. To enter “2”, press the [2] key and rotate the sub dial clockwise for one click.

56 4. Press the [PASS] key to delete. 5. Press the [MHz] to exit from this menu. 8-1-2-8 LOCKING OUT UNWANTED ACTIVE FREQUENCIES (PASS) I

57 8-1-2-9 DELETING PASS CHANNELS To delete one pass channel, perform the following steps: 1. Press and hold the [PASS] key for two seconds. 2. R

58 To activate the Cyber search function, perform the following steps: 1. Press and hold the [SRCH] key for two seconds and Cyber search will start.

5 1 INTRODUCTION 1-1 INTRODUCTION Thank you for purchasing the AR5001D Digital Processing Communications receiver. As the successor to the AR5

59 8-2-2 SEARCH PAUSE The search pause parameter determines how long the receiver will remain on an active frequency before resuming searching eve

60 3. Rotate the sub dial to select the search delay. If “hold” is selected, the receiver will stop searching when the signal is received

61 To delete all auto stored frequencies on the memory bank, press the [PASS] key. 4. To confirm entry, press the [MHz] key. To set other

62 9-1 CONFIGURE LAMP The AR5001D is equipped with high intensity green LEDs to illuminate the LCD and keypad when operating in areas of low level

63 9-3 CONFIGURE BPS (BAUD RATE) The Remote BPS Set menu is used to configure the communication port control settings as it is important that they

64 Press the [DOWN] key four times to select “SQL SKIP” in reverse contrast. Rotate the sub dial to select either on or off. Press the [MHz] key t

65 4. Rotate the main dial to select Antenna 1. 5. Rotate the sub dial to select the desired program number 0. If the programme

66 3. Press the [FUNC] key, and then press the [kHz] key. 4. When the configuration menu is displayed, press the [DOWN] key seven times to selec

67 5. Press the [MHz] key. 6. Using the numeric keypad, enter the desired file name. (No file extension required.) A text of up to eight

68 4. When the configuration menu is displayed, press the [UP] key five times to select “READ FROM SD” in reverse contrast. 5. P

6 Main features:  Wide frequency coverage: 40 kHz to 3.15 GHz, with no interruptions (Cellular blocked for the US consumer version)  45.05

69 7. Formatting will start. 9-12 CONFIGURE VERSION To display the current firmware version of the AR5001D, perform the following steps: 1.

70 5. After initialized, the receiver will be powered off automatically, and then restart. 9-14 CONFIGURE MEMORY CHANNEL ASSIGNMENT A number

71 level from the range of 0 ~ 9 dB. 3. Press the [MHz] key to accept the entry and return to a standard display. Alternatively, press th

72 1. Press the [FUNC] key, and then press the [0] key. 2. Press the [DOWN] key three times to select “NB” in reverse contrast. 3. Rotate the su

73 2. Press the [DOWN] key five times to select “IF-SFT” in reverse contrast. 3. Rotate the sub dial to select the shift frequency from the range

74 4. Press the [MHz] key to accept the entry and return to a standard display. Alternatively, press the [CLR] key to abort entry, or press the

75 10-10 DTMF (DUAL TONE MULTI FREQUENCY) DTMF tones are used by many VHF/UHF communications services and amateur radio operators to control swit

76 5 5 MHz ~ 10 MHz 6 10 MHz ~ 15 MHz 7 15 MHz ~ 20 MHz 8 20 MHz ~ 25 MHz 5. Press the [MHz] key to accept the entry and return to a standard di

77 2. Press the [DOWN] key several times to select “VIDEO IMG” in reverse contrast. 3. Rotate the sub dial to select normal or reverse. 4. Press

78 11-2 SUB DIAL SETTING The sub dial can be used to select the receive frequency in three different ways. • Same step size as the main dial •

7 1-2 TAKE CARE OF YOUR RECEIVER There are no internal operator adjustments needed. In the unlikely event of service being required, please contact

79 • While scanning Press the [SCAN] key, and then press the [MHz] key. The active channel will be transferred to V

80 The squelch parameter ranges are off and 1 ~ 7. To set the voice squelch parameter, perform the following steps: 1. Press the [FUNC] key, and the

81 11-4-2 HF (HIGH PASS FILTER) The audio high pass filter limits the audio base response improving intelligibility in certain circumstances. Ther

82 11-4-4 CW PITCH Comfortable listening to CW is usually centered around a tone of 700 Hz to 800 Hz. However, the center frequency may be changed

83 4. Using the main dial, adjust hours. 5. Using the sub dial, adjust minutes. 6. Press the [DOWN] key to select “TEXT” in reverse format. 7. A

84 a) Press the [4] key. Rotate the sub dial to select “U”. b) Press the [UP] key to move the cursor to the right. c)

85 5. Press the [DOWN] key to select “ACT” in reverse contrast. 6. Rotate the sub dial to select from “BEEP”, “RADIO”, “RADIO (SD REC, SQL SKIP ON

86 3. When the preset time has arrived, either the beep will sound or the radio will automatically switch on (the receive frequency will

87 Note: Depending upon the frequency and mode stored as priority, an audible click may be heard when the priority function is in operation. This is

88 The normal position for the AR5001D RF gain control is fully counterclockwise when set at its most sensitive. As the control is rotated clockwise,

8 Operating anomalies Should the AR5001D appear to behave strangely, normal operations may be easily achieved by performing the following steps: 1.

89 13 OPTIONAL ACCESSORIES 13-1 I/Q UNIT With this optional internal I/Q unit, a full 1 MHz of bandwidth activity (25MHz to 3.15GHz) can be store

90 13-6 ANTENNAS Note: DA753G is sold under the name DS3000A in the U.S. DA3200 16 element disconeDA753G compact disconeDA5000 commercial g

91 14 SPECIFICATIONS

92 15 LIMITED WARRANTY (USA only) AOR USA, Inc. (AOR) warrants its receivers as described below: AOR will repair or exchange equipment as a result

93 Some states do not allow limitations on how long an implied warranty lasts and may not allow the exclusion of incidental or consequential damages.

94 Manufacturer: AOR, LTD. 2-6-4, Misuji, Taito-Ku,